Search Results

Standard

High-Carbon Cast-Steel Shot

2005-07-25

HISTORICAL

J827_200507

This SAE Recommended Practice describes chemical composition and physical characteristic requirements for high-carbon cast-steel shot to be used for shot peening or blast cleaning operations.

Standard

Metallic Shot and Grit Mechanical Testing

2005-07-25

HISTORICAL

J445_200507

This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.

Standard

Cast Shot and Grit Size Specifications for Peening and Cleaning

2005-07-25

HISTORICAL

J444_200507

This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E 11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.

Standard

High-Carbon Cast-Steel Grit

2005-07-25

HISTORICAL

J1993_200507

This SAE Recommended Practice describes the chemical composition, and physical characteristic requirements for high-carbon cast-steel grit, to be used for blast cleaning and etching operations.

Standard

Shot Peening Coverage

2003-01-09

HISTORICAL

J2277_200301

This SAE Recommended Practice provides procedures for determining shot peening coverage. Effectiveness of shot peening is directly dependent on coverage. Inadequate or excessive coverage may be detrimental to fatigue.

Standard

Procedures for Using Standard Shot Peening Test Strip

2003-01-09

HISTORICAL

J443_200301

This SAE Recommended Practice provides uniform procedures for using the standard shot peening test strips reported in SAE J442. Standard test strips are used to establish saturation, determine intensity, monitor repeatability of the shot peening machine operations, and can be used to predict a desired result on a part. It is recommended that the standard test strip A be used for intensities that produce arc heights of 0.10mm A (0.004 inch A) to 0.60 mm A (0.024 inch A). For intensities below 0.10 mm A (0.004 inch A), the standard N strip is recommended, and for intensities above 0.60 mm A (0.024 inch A), the standard C strip is recommended. The process of shot peening, in common with many other processes, cannot at present be adequately controlled by nondestructive inspection of the peened parts, therefore, it is necessary to control the process itself to achieve consistent, reliable results.

Standard

Test Strip, Holder, and Gage for Shot Peening

2001-12-10

HISTORICAL

J442_200112

This SAE Standard defines requirements for equipment/supplies to be used in measuring shot peening intensity. Guidelines for the use of these articles (test strip, holding fixture, and gage) are also included.

Standard

Shot Peening

2000-08-01

HISTORICAL

J2441_200008

This SAE Standard covers the engineering requirements for peening surfaces of parts by impingement of metallic shot, glass beads, or ceramic shot.

Standard

HIGH-CARBON CAST-STEEL SHOT

1996-09-01

HISTORICAL

J827_199609

This SAE Recommended Practice describes chemical composition and physical characteristic requirements for high-carbon cast-steel shot to be used for shot peening or blast cleaning operations.

Standard

HIGH-CARBON CAST-STEEL GRIT

1996-09-01

HISTORICAL

J1993_199609

This SAE Recommended Practice describes the chemical composition, and physical characteristic requirements for high-carbon cast-steel grit, to be used for blast cleaning and etching operations.

Standard

METALLIC SHOT AND GRIT MECHANICAL TESTING

1996-04-01

HISTORICAL

J445_199604

This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.

Standard

TEST STRIP, HOLDER, AND GAGE FOR SHOT PEENING

1995-01-01

HISTORICAL

J442_199501

This SAE Standard defines requirements for equipment/supplies to be used in measuring shot peening intensity. Guidelines for the use of these articles (test strip, holding fixture, and gage) are also included.

Standard

HIGH CARBON CAST STEEL SHOT

1994-07-01

HISTORICAL

J827_199407

This SAE Recommended Practice describes chemical composition, hardness, microstructure, and physical characteristic requirements for high carbon cast steel shot to be used for shot peening or blast cleaning operations.

Standard

CUT WIRE SHOT

1993-06-01

HISTORICAL

J441_199306

This SAE Recommended Practice is considered to be tentative and is subject to modification to meet new developments or requirements. It is offered as a guide in the selection and use of cut wire shot.

Standard

CAST SHOT AND GRIT SIZE SPECIFICATIONS FOR PEENING AND CLEANING

1993-05-01

HISTORICAL

J444_199305

This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E 11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.

Standard

CAST STEEL GRIT

1993-03-01

HISTORICAL

J1993_199303

This SAE Recommended Practice describes the chemical composition and the physical requirements for high carbon cast steel grit.

Standard

SPECIFICATIONS FOR LOW CARBON CAST STEEL SHOT

1991-06-01

HISTORICAL

J2175_199106

This SAE Recommended Practice describes chemical analysis, hardness, microstructure, and physical characteristic requirements for low carbon cast steel shot to be used for shot peening or blast cleaning operations.

Standard

CAST STEEL SHOT

1990-03-01

HISTORICAL

J827_199003

This SAE Recommended Practice describes chemical analysis, hardness, microstructure and physical characteristic requirements for cast steel shot to be used for shot peening or blast cleaning operations.

Standard

SIZE CLASSIFICATION AND CHARACTERISTICS OF CERAMIC SHOT FOR PEENING

1987-05-01

HISTORICAL

J1830_198705

This specification covers characteristics for chemistry, microstructure, density, hardness, size, shape and appearance of zirconium oxide based ceramic shot, suitable for peening surfaces of parts by impingement.

Standard

CUT WIRE SHOT

1987-05-01

HISTORICAL

J441_198705